EDIFIER-X6-Manual-5

EDIFIER X6 Manual | Instructions & Troubleshooting 2022

The EDIFIER X6 have the IP54 water and dust resistance, 5 hours of playtime + 15 hours using the charging case, Bluetooth 5.0, Dual Mic CVC for clear calls and voices, a Qualcomm 3020 chipset with aptX codec, and much more. Learn how to use them with this new EDIFIER X6 Manual.

EDIFIER X6 Manual | Pairing & Charging Instructions

EDIFIER X6 Manual | How to Pair / Connect?

To iOS and Android phones

Step 1: Open the lid of the charging case and take the earbuds out. After that, a blue light will flash one time, and they will turn on automatically.

Step 2: Place the earbuds into the charging case, but keep the lid open so they don’t turn off.

Step 3: Press and hold the button on the back case for 3 seconds to enter Bluetooth pairing mode. A red and blue light will start flashing quickly.

Step 4: Press and hold the button on the back case for 8 seconds to pair the earbuds to each other and, after that, they will be ready to pair with any device. A blue light will start flashing quickly.

Step 5: Go to the device’s Bluetooth settings.

Step 6: Select “EDIFIER X6 L” and “EDIFIER X6 R”. If a password is needed, type “0000”.

Step 7: After that, the pairing will be done.

To PC (Windows)

Step 1: Turn on Window’s Bluetooth.

Step 2: Go to the settings.

Step 3: Go to “Bluetooth and other devices”.

Step 4: Click on “Add device”.

Step 5: Open the lid of the charging case and take the earbuds out. After that, a blue light will flash one time, and they will turn on automatically.

Step 6: Place the earbuds into the charging case, but keep the lid open so they don’t turn off.

Step 7: Press and hold the button on the back case for 3 seconds to enter Bluetooth pairing mode. A red and blue light will start flashing quickly.

Step 8: Press and hold the button on the back case for 8 seconds to pair the earbuds to each other and, after that, they will be ready to pair with any device. A blue light will start flashing quickly.

Step 9: Select “EDIFIER X6 L” and “EDIFIER X6 R”. If a password is needed, type “0000”.

Step 10: After that, the pairing will be done.

EDIFIER-X6-Manual-1

EDIFIER X6 Manual | How to Wear?

Step 1: Take both earbuds out of the charging case.

Step 2: Identify the left and right earbuds.

Step 3: Choose the ear tips that best suit your ears.

Step 4: Insert the headphones into the inner canal of the ears.

Step 5: Rotate for the best possible comfort and best fit, and make sure that the microphone is pointing to the mouth.

EDIFIER X6 Manual | How to Turn On and Off?

Turn on: Open the lid of the charging case and take the earbuds out. After that, a blue light will flash one time, and they will turn on automatically.

Turn off: Place the earbuds into the charging case and close its lid. After that, the earbuds will turn off automatically.

EDIFIER-X6-Manual-2

How to Control? / How to Operate? – Instructions

  • Play or pause music: Press the multifunction touch button on any of the earbuds two times.
  • Answer an incoming call: Press the multifunction touch button on any of the earbuds two times.
  • End a current call: Press the multifunction touch button on any of the earbuds two times.
  • Activate the voice assistant: Press the multifunction touch button on any of the earbuds three times.

EDIFIER X6 Manual | How to Activate Mono Mode?

To activate or deactivate the mono mode in the EDIFIER X6, all you have to do is to pair the earbuds to the device and take out one of the earbuds from the charging case. It will start working by itself.

EDIFIER-X6-Manual-3

EDIFIER X6 Manual | How to Charge?

Earbuds

To charge the earbuds, all you have to do is to place them into the charging case and close the lid. The earbuds will start charging automatically.

Charging case

To charge the charging case, all you have to do is to connect the case to a USB charger or charging port with the included USB-A to C cable. It will start charging automatically.

EDIFIER X6 Manual | How to Reset?

Step 1: With the lid open and the earbuds inside of the charging case, press and hold the button on the case for about 12 seconds.

Step 2: After that, the resetting will be done.

EDIFIER-X6-Manual-4

EDIFIER X6 Manual | LED Light Status

Earbuds

  • A red and blue light flashing quickly: The earbuds turn into Bluetooth pairing mode.
  • A blue light flashing quickly: The earbuds pair to each other and are ready to pair with any device.
  • A red light flashing quickly on both earbuds: The pairing was successful.

Some Common Earbuds Problems & Troubleshooting

Left / Right / One side of the earbuds have stopped working

If this happens, it may be because it is low on battery or it did not connect correctly with the device. To fix this, you can do the following:

1. Try charging the earbud that is not working or both, placing them in the charging case.

2. Try factory resetting the earbuds.

3. Check if the earbuds are operating within a normal working range

If that doesn’t work, the earbud is probably faulty, and I can go for a refund or replacement of it.

Left / Right / One side of the earbuds has a low volume

If this happens, it may be because the earbuds are dirty or the volume is set low. To fix this, you can do the following:

1. Try cleaning the earbud using a cotton swab or carefully clean the mesh with a pin.

2. Try factory resetting the earbuds.

Microphone not working

If this happens, it can be because the microphone is muted, or the earbuds are badly positioned. To fix this, you can do the following:

If the microphone is muted, check the device microphone volume. If that doesn’t work, that means that there might be a defect in the earbud, so try replacing them or get a refund.

EDIFIER X6 earbuds not connecting to Windows/laptop/PC

If the earbuds are earbuds not connecting, it can be because the Bluetooth on the computer has a pairing problem. To fix this, you can do the following:

1. Try disabling Bluetooth from nearby devices >>> then activate pairing mode of the earbuds, pair and connect earbuds from Settings >>> Bluetooth & other devices >>> Add a new device >>>> elect Bluetooth,

2. Try uninstalling and reinstalling the Bluetooth driver, or update the Bluetooth driver. All can be done in Manage >>> Device Manager, reset earbuds (if available), and then repeat the step.

3. Try resetting the earbuds.

EDIFIER-X6-Manual-5

FAQs

Are EDIFIER X6 waterproof?

No, the EDIFIER X6 are not waterproof (IPX6 and up). They have a rating of IPX4, which means they’re splash and sweat-resistant.

Does EDIFIER X6 have a microphone?

Yes, the EDIFIER X6 have integrated microphones.

Do EDIFIER X6 have low latency/gaming mode?

No! The EDIFIER X6 don’t have a low latency/gaming mode.

How to know when EDIFIER X6 are fully charged?

When the earbuds are charging, a light turns on. When fully charged, that light turns off.

Can EDIFIER X6 connect to PC and Laptop?

Yes, the EDIFIER X6 can connect to PCs, laptops, and tablets.

We hope you now know how to operate the earbuds from the above EDIFIER X6 Manual. Want to know anything about them? Do not hesitate to ask in the comments section.